鋁板深加工，你知道多少呢?相信很多人和小編一樣是個小白吧!沒有關系，讓我們跟著鋁板生產廠家一起來看看吧
How much do you know about deep processing of aluminum plate? I believe many people are just like Xiaobian! It doesn't matter. Let's take a look with the aluminum plate manufacturer
鋁板深加工的步驟如下：
The steps of deep processing of aluminum plate are as follows:
選板：我們須要選擇那些合金鋁板硬度不高，不易彎曲斷裂的，所以，在原材料上面須選用鋁板。
Plate selection: we need to select those alloy aluminum plates with low hardness and not easy to bend and fracture. Therefore, aluminum plates must be selected for raw materials.
在運輸和加工過程中的保護：根據客戶的要求，將原材料粘貼在一側(光滑表面)或兩側，以避免運輸或加工過程中損壞零件表面。
Protection during transportation and processing: according to the customer's requirements, the raw materials are pasted on one side (smooth surface) or both sides to avoid damage to the part surface during transportation or processing.
零件的表面沖裁：零件的沖裁和沖裁，在送料和沖裁前應調整上下模間隙。
Surface blanking of parts: for blanking and blanking of parts, the clearance between upper and lower dies shall be adjusted before feeding and blanking.
彎曲：為了盡量減少對板材內部結構的損壞，應增加彎曲角度，以滿足產品的使用條件;彎曲方向應垂直于鋁板的紋理方向。
Bending: in order to minimize the damage to the internal structure of the plate, the bending angle should be increased to meet the service conditions of the product; The bending direction shall be perpendicular to the grain direction of the aluminum plate.

之后是焊接：根據板料厚度和材料性能，選擇相應的焊絲和焊接類型，調整相應的電壓范圍、電流范圍和氣壓范圍。
Then welding: according to the sheet thickness and material properties, select the corresponding welding wire and welding type, and adjust the corresponding voltage range, current range and gas pressure range.
鋁板的深加工也要注意零件表面的沖壓?jiǎn)栴}。在鋁板切割和沖壓機之前，須調整數控刀片左右模具的間隙。與普通冷軋鋼板相比，鋁板之間的間隙應該減少，以防止沖壓傷口的毛刺過大。
In the deep processing of aluminum plate, attention should also be paid to the stamping of the part surface. Before the aluminum plate cutting and stamping machine, the clearance between the left and right dies of the NC blade must be adjusted. Compared with ordinary cold-rolled steel plate, the gap between aluminum plates should be reduced to prevent excessive burr of punching wound.
鋁板深加工也要注意鋁板加工過程中的彎曲，其彎曲標準是在達到商品應用標準的情況下，能盡可能地增加彎曲的內角，這樣可以防止板材內部機構的損壞，但須注意的是，鋁板的彎曲方向須是垂直的，不能是平行的。
In the deep processing of aluminum plate, attention should also be paid to the bending during the processing of aluminum plate. The bending standard is to increase the internal angle of bending as much as possible when the commercial application standard is met, so as to prevent damage to the internal mechanism of the plate. However, it should be noted that the bending direction of aluminum plate must be vertical and not parallel.
關于鋁板深加工的相關步驟以及它的注意事項就到這里了，如果您有疑惑就來我們網站http://jxhupan.com聯系吧，有關人員為您解惑答疑。
That's all about the steps and precautions of aluminum plate deep processing. If you have any questions, please come to our website http://jxhupan.com Contact us and relevant personnel will answer your questions.